Guide · Homeowners · 4 min read · Updated 17 November 2026
How Much Do Electric Gates Cost in the UK? (2026 Guide)
Short answer
In the UK in 2026, automating existing double swing gates typically costs £1,800–£3,200. Steel double swing gates with automation cost £4,500–£8,500, hardwood gates £6,000–£11,000, and a sliding gate £6,500–£13,000. Underground motors add from £1,200 per pair, and a video intercom or GSM access control adds £450–£1,500. The gate material, the groundworks and the distance to a power supply drive most of the difference.
Typical electric gate prices in 2026
Electric gate quotes vary more than almost any other home improvement, because you are buying three things at once: the gates, the automation and the groundworks that hold it all up. A homeowner with sound timber gates and a socket in the garage can be automated for a fraction of the cost of a new sliding gate on a sloping drive with no power nearby. The table below shows guide prices for typical UK homes in 2026, including fitting.
These figures assume a standard residential driveway, normal ground conditions and a power supply within a sensible distance. Bespoke designs, very wide openings and listed or conservation area properties can sit above the ranges shown.
| Job | Guide price | What it usually includes |
|---|---|---|
| Automation kit on existing double swing gates | £1,800–£3,200 | Ram motors, control board, photocells, warning light, two fobs |
| Steel double swing gates with automation | £4,500–£8,500 | Made-to-measure metal gates up to about 4m, new posts, motors, safety kit |
| Hardwood double swing gates with automation | £6,000–£11,000 | Iroko or oak on steel frames, heavier motors and posts |
| Sliding gate, track or cantilever | £6,500–£13,000 | Concrete base or track, rack, motor; cantilever at the upper end |
| Underground motors instead of rams | from £1,200 | Foundation boxes, drainage and motors, per pair |
| Video intercom or GSM access control | £450–£1,500 | Unit, cabling to the house or app set-up |
What pushes the price up
Gate weight is the starting point. A solid hardwood leaf can weigh two or three times as much as an open steel railing design, and it catches the wind like a sail. That means a heavier frame, stronger posts or piers and a more powerful operator. Width matters for the same reason: a 2m leaf puts far more leverage on the hinge post than a 1.5m leaf.
The ground is the next big variable. A drive that rises behind the gates may need rising hinges, regrading or a switch to a sliding system. Sliding gates need a level concrete strip to run on, plus enough run-back space beside the opening. Every metre of armoured cable between the house and the gate means more trenching, and crossing a block-paved drive costs more than running along a lawn edge.
- Solid infill or hardwood leaves that need stronger motors
- New brick piers or steel posts instead of reusing sound ones
- Long cable runs or trenching through hard surfaces
- Sloping drives needing rising hinges or a sliding gate
- Underground motors, which need foundation boxes and drainage
- Video intercoms, number-plate cameras or exit loops
Ram, articulated arm or underground motors
Most domestic swing gates use ram motors, which bolt between the post and the gate and push it open. They are the most cost-effective option and work well where the posts are wide enough to mount brackets. Articulated arm motors suit thick piers where a ram cannot get the right geometry. Underground motors sit in a sealed box beneath each hinge, leaving the gates looking unmotorised.
Underground systems cost more because each box needs a concrete surround and a drain so water does not sit around the motor. On clay or in low spots that drainage is not optional. If the look of the gates matters more than budget, underground motors are worth the extra; if not, a well-fitted ram is a reliable choice.
Costs people forget to budget for
A good quote should spell out the safety work, not just the hardware. Under BS EN 12453, a powered gate must be designed so it cannot crush, shear or strike someone with excessive force. That usually means photocells at more than one height, safety edges on closing edges and a force test with a calibrated meter at handover. Cheaper quotes sometimes leave this out, and it is the part that protects children, pets and visitors.
Electrical work is another line to check. A new outdoor circuit should be installed to BS 7671 and, in England, it falls under Part P of the Building Regulations, so it must be done or certified by someone able to notify it. Ask whether the quote includes that, plus making good any paving or lawn that has been trenched.
How to get an accurate quote
A site visit is the only way to price electric gates properly, but you can make it quicker and more accurate. Measure the opening between the posts, note whether the drive slopes up or down behind the gates, and work out roughly where the nearest power supply is. Decide how you want to open the gates: fobs only, a keypad for deliveries, or a video intercom you can answer from your phone.
When you compare quotes, line them up item by item. One may include new posts and full safety kit while another assumes the existing posts will do and leaves out safety edges. The cheapest figure is not always the cheapest outcome if the gates later need upgrading to be safe.
Running costs after installation
The spend does not stop at handover, though ongoing costs are modest. The motors themselves use very little electricity, because they only run for a few seconds each cycle and sit on standby the rest of the time. The bigger ongoing cost is servicing. An annual visit to check forces, clean photocells, grease hinges and test the battery backup is the best way to keep the gate safe and avoid an emergency call-out.
Parts wear at different rates. Remote fobs get lost and need replacing, backup batteries usually last a few years, and control boards can be damaged by lightning or water getting into a poorly sealed housing. Hardwood gates need re-oiling every year or two to stop the timber greying and moving, and painted steel gates benefit from touching up chips before rust takes hold.
Budgeting a small amount each year for servicing and occasional parts is far cheaper than letting a gate run until it fails. Motors that strain against a sagging leaf or a dirty track wear out years early, and that replacement is a much bigger bill than routine care.
Questions people also ask
Is it cheaper to automate my existing gates?
Usually, yes. Automating sound existing gates costs around £1,800–£3,200, compared with £4,500 or more for new steel gates with motors. The catch is that the gates and posts must be strong, square and swing freely by hand. Rotten timber, weak hinges or leaning posts need sorting first, and sometimes replacement works out better value.
Do electric gates need planning permission?
Often not. In England, permitted development generally allows gates up to 1 metre high next to a road used by vehicles and 2 metres elsewhere. Taller gates, listed buildings and conservation areas may need permission. Gates must also not open outwards over a public road or footpath under the Highways Act 1980.
How long does electric gate installation take?
Automating existing gates is often a one or two-day job. New gates on new posts usually take two to four days on site, with concrete left to cure before hanging. Bespoke gates have a manufacturing lead time of several weeks before installation, and sliding gates with new concrete bases can take a little longer.
Written and checked by the Electric Gate Installation team. Read our editorial policy.
More guides
Sliding vs Swing Electric Gates: Which Is Right for Your Drive?
Choose swing gates if you have a level drive, enough space behind the gates for them to open, and want the lower cost. Choose a sliding gate if the…
Electric Gate Safety Rules in the UK: What Homeowners Must Know
In the UK, powered gates are treated as machinery. A new installation should follow the Supply of Machinery (Safety) Regulations 2008, with a risk…
Can You Automate Existing Gates? A Practical Guide
Yes, most existing gates can be automated if they are structurally sound, hang square and swing freely by hand, and the posts can carry the extra…
How to Choose an Electric Gate Installer: Checks Before You Book
Choose an electric gate installer who carries out a site risk assessment, fits safety devices in line with BS EN 12453, force-tests the gate at…
Get a free electric gate installation quote
Tell us what you need and we'll come back with a clear price.
Request a quote