Electric Gate Installation

Guide · Homeowners · 3 min read · Updated 17 November 2026

Can You Automate Existing Gates? A Practical Guide

Short answer

Yes, most existing gates can be automated if they are structurally sound, hang square and swing freely by hand, and the posts can carry the extra load. A typical automation kit for existing double swing gates costs £1,800–£3,200 fitted, including ram motors, control board, photocells, warning light and fobs. Rotten timber, sagging leaves or weak posts must be repaired or replaced first.

Can You Automate Existing Gates? A Practical Guide

What makes a gate suitable for automation

A motor does not fix a bad gate; it exposes it. If a gate drags, binds or needs lifting to latch, a motor will strain against it, wear out early and may not stop safely when it meets an obstruction. Before anything else, an installer will open and close each leaf by hand to feel for stiffness, check that the leaves meet cleanly and look at how the hinges are fixed.

The posts or piers matter as much as the gates. A motor puts extra leverage on the hinge post every time it opens and closes. Timber posts that have started to rot at ground level, or brick piers with loose hinge fixings, need attention before automation.

  • Gates swing freely by hand through their full travel
  • Leaves are square, rigid and do not sag
  • Hinges are sound and securely fixed
  • Posts or piers are solid at ground level
  • There is space on the post to mount motor brackets
  • A power supply can be brought to the gate

What an automation kit includes

A standard retrofit package for double swing gates includes a motor for each leaf, a control board in a weatherproof housing, a pair of photocells, a flashing warning light and a couple of remote fobs. Most installers also add an electric lock or rely on self-locking motors, and a battery backup if you want the gate to run during a power cut.

From there, you can add access control. A keypad lets visitors with a code in. A GSM unit lets you open the gate from your phone. A video intercom wired to the house lets you see who is there. These typically add £450–£1,500 depending on the system.

ItemGuide priceNotes
Ram motor kit for double swing gates£1,800–£3,200Motors, board, photocells, light, two fobs
Underground motors instead of ramsfrom £1,200 extraPer pair, with foundation boxes and drainage
Video intercom or GSM control£450–£1,500Includes cabling or app set-up
Replacement timber post (if needed)Quoted on surveyDepends on post type and fixing

Common problems found on survey

Timber gates are the most common candidates and the most likely to need work. Older ledged and braced gates often sag at the latch end, and solid board gates can be too heavy or too exposed for a basic motor. Wrought iron gates may have worn hinge pins that let the leaf wobble. Gates that open outwards over a footpath or road cannot simply be automated as they are, because gates must not open outwards over the highway.

Ground levels cause trouble too. If the drive rises behind the gates, the bottom edge may scrape part-way through its swing, which a motor will struggle with. Fixing that may mean trimming the gates, fitting rising hinges or regrading.

Making the retrofit safe

Adding motors turns a manual gate into a machine, and whoever automates it takes responsibility for its safety. The installer should carry out a risk assessment, fit photocells and, where needed, safety edges, then measure the closing forces with a force meter in line with BS EN 12453. You should receive a technical file and a declaration of conformity, plus an electrical certificate for the new circuit.

Be wary of quotes that only list motors and fobs. Safety devices and commissioning are a core part of the job, not optional extras.

When new gates are the better option

Sometimes the honest answer is that the existing gates are not worth automating. If they need new posts, new hinges, structural repairs and trimming, the combined cost can approach that of new steel gates built for automation from the start. New gates can also be designed lighter or with a more open pattern to reduce wind loading, which helps the motors last.

A good surveyor will price both routes so you can compare the real cost over the life of the gate, not just the figure on day one.

Preparing for the survey and fitting day

A little preparation saves time and helps the installer give a firm price. Before the survey, open and close each gate by hand and note anything that sticks or scrapes. Find your consumer unit and think about where a new circuit could start, whether that is the house, a garage or an outbuilding. Measure the distance roughly so you can discuss the cable route, and point out any buried pipes, drains or cables you know about.

Decide how the gate will be used day to day. If you have regular deliveries, a keypad or GSM unit saves you walking out to open the gate. If you want to see visitors, a video intercom needs cabling to the house, which is easiest to lay at the same time as the power cable.

On fitting day, keep the drive clear of cars and make sure the team can reach the consumer unit. Expect some trenching across a lawn or border, which a good installer will backfill and tidy. Allow time at the end for the handover so you understand the fobs, the manual release and the safety checks.

Questions people also ask

Can wooden gates be automated?

Yes, as long as the timber is sound, the gate frame is rigid and the posts are solid. Heavy solid hardwood gates need stronger motors and posts, and exposed sites need careful motor selection because of wind. Sagging or rotten gates should be repaired or replaced before motors go on.

Do I need a power supply at the gate?

You need power brought to the control board, usually by an armoured cable from the house or garage laid in a trench. Low-voltage cable then runs to the motors and safety devices. Solar kits exist for light gates on sites with no mains, but they suit low-use gates with good sun exposure.

Can I still open the gates if the power fails?

Yes. Every motor has a manual release, usually opened with a key, that lets you push the gates by hand. Many installations also include a battery backup that runs the gates for a number of cycles during a power cut. Ask your installer to show you how the release works at handover.

Written and checked by the Electric Gate Installation team. Read our editorial policy.

Get a free electric gate installation quote

Tell us what you need and we'll come back with a clear price.

Request a quote